raingutter regatta sail tips

likar March 07, 2022 raingutter , regatta , sail Comment

All boats will be inspected before they are allowed to compete. This is a chance for your Scout to be part of a team during boat construction and to enjoy the spirit of friendly competition with his peers.

Tips On Building A Raingutter Regatta Pack 495 Albuquerque Nm

The hull of the boat can be no longer than 7 and no shorter than 6 12.

. Racing Procedure The boats are propelled by boys blowing into the sails. Air cannot pass through a sail made from a rigid material. It should not rock but if it does place sandpaper on the flat surface and gently sand the bottom to make it even.

The Outriggers must be no longer than 7 or shorter than 6 ½. NO substitutions are allowed OutriggersHull. These Raingutter boats can be built the same day they are raced or taken home to build or built as a group during a meeting.

How to Build a Raingutter Regatta Boat for Boy Scouts. Boats may not be modified. This will remove as much moisture from the wood as possible which will make the block of wood lighter.

Each scout has an assigned boat number printed on a label affixed to your boat kit. Decorate the sail any way you like. Raingutter Regatta Tips Pack 410 1.

Every other year the cub scouts in Pack 61 get a chance to compete in the Raingutter Regatta. Cut the hull down the centerline. Place the cookie sheet with the block of wood into the oven.

LET THE BOYS DO IT. The boys and an adult should make the boat together. The rules for the Raingutter Regatta are fairly simple.

The boys build boats from standard BSA kits supplied by the pack. You may trim the sail if needed but it cannot be folded. Raingutter Regatta Rules and TipsHints Sheet Nothing may extend past front point or rear point of outriggers so maximum total boat length is 6 34 inches Maximum boat hull width not counting sail is 3 38 inches if you have parts sticking out from sides you will hit the gutter and go slow Must use all parts from kit 2 outriggers.

For best results paint or otherwise seal the hulls of the boat that will be touching the water. The boats are propelled through the water by blowing on the sail. The hull is 2 12 wide and the sail is 2 12 wideThe hull is made of Dow Corning Styrofoam.

Making a boat is very easy. The best technique for winning is just to practice blowing really hard in a small area. I didnt have much luck with the aluminum foil boat.

Please follow the assembly directions on the package and allow the boys to decorate in any manner they choose. This is an excellent place for decals and stickersboys love both. Boats must be made from the official BSA Raingutter Regatta Trimaran Boat Kit.

The mast must be 6 12 from the deck to the top. The foam does not absorb water. Bake the Pinewood Derby block of wood for two hours.

The bottom edge of the sail needs to be about 12 inch above the deck of the boat. Put your boat number on the sail - youre done. 10The keel and rudder can be altered and moved their use is not required but is recommended.

Special thanks to the other. Use a bendable straw for the mast. The sail may be no larger than the material provided.

Zaiden builds his Rain Gutter Regatta for Cub Scouts. Make any needed adjustments and when level fill to about 12 from top. Ad Check Out Rain Gutter Regata on ebay.

Bend the straw and tape the short end to the bottom of your boat. The actual race will involve a set of two raingutters. Since this is.

All parts 2 outriggers polymer hull mast sail and 4 screws provided in the kit must be used in the boat construction. Please feel free to give guidance and minimal assistance. Fill Your Cart With Color today.

If the sail is too low the corners rub against the gutter or dip in the water. Position the sail on the mast. Preheat your oven to 250 degrees.

A small sail on the back of the deck reduces forward tipping. The hull is easily shaped with sandpaper. The dull side can be.

Use a bit of glue or tape on the mast and sail so they dont come out or spin when blown on. You need to use the keel and rudder that were supplied. Cut a triangular sail from paper.

An area to show off your decorations is on the sail. Start with the boats stern touching the end of the raingutter. The sail provided in the BSA kit has a glossy side and a dull side.

Next remove the pontoons and use super fine sandpaper 400 grit at least to smooth all the surfaces. Trim the hull to make it symmetric. Mine just didnt want to go anywhere.

Place the Pinewood Derby block of wood on the cookie sheet. Pack 469 - Official Raingutter Regatta Rules Trimaran Series The Raingutter Regatta is a parent-son project. Please feel free to give guidance and minimal assistance appropriate to the age of your Scout as he builds his Rain gutter Regatta boat.

NO substitutions are allowed 2. I suspect its because I had a hard time imagining how to shape the boat. Here are some tips for building a winning design.

The vertical position of the sale is important. Curved up pontoon tips keep water under the pontoons. The boys make a small lightweight sail boat using a kit supplied by the pack and then race their boats against each other.

About 34 from the top of the mast either glue the sail to it or attach securely with tape. 2 outriggers polymer hull mast sail and 4 screws provided in the kit must be used in the boat construction. You must use the sail provided in the kit.

You do want to glue your sail in placeat the very minimum and having flat rails on the bottom helps. The boys blow air on the sails of the boat with a straw to. Raingutter Regatta Tips Be sure to keep these important points in mind while you build your boat.

Attach bottom of sail in a similar manner. This foam is a closed cell foam. Let your scout decorate the hull and sail insert the mast and attach the sail.

The Raingutter Regatta is a parent-Scout project. He researched many videos and made his own version of the winning regattas. Too high and your boat will.

It will take practice before hand. The boat should use every part from the BSA kit. Some scouts use a straw to blow to concentrate the air.

Place the boat on a smooth flat surface like a table top and gently see if it rocks side to side or fore and aft. Refer to the catamaran template in Appendix G for the following steps. Some take deeper breathes.

With gutters in place put a small amount of water into each to make sure they are level.